Hutox 100unit: A Professional Reference for Reconstitution, Dilution, and Handling

Hutox 100unit is a botulinum toxin type A product developed by Huons Co., Ltd. of South Korea. It is supplied as a sterile, vacuum-dried, white or light-yellow lyophilized powder in a transparent glass vial. Before any preparation, professionals should perform a visual inspection of the unopened vial.

Key inspection points include:

• Seal Integrity: Confirm the protective cap and rubber stopper are intact and have not been tampered with.
• Vial Condition: Check for any cracks, chips, or damage to the glass vial.
• Product Appearance: The content should be a fine, dry powder. Discard the vial if any discoloration, moisture, or foreign particles are present.

Verifying the packaging integrity is the first step in ensuring product quality for your clinic. It is one of several Korean-manufactured toxins available to clinics, alongside alternatives such as Nabota 100unit and Re N Tox.

To properly reconstitute Hutox 100unit, trained personnel must use aseptic techniques and have the following materials available:

• One vial of Hutox 100unit.
• Preservative-free, sterile 0.9% sodium chloride (saline) solution for injection.
• An appropriately sized sterile syringe (e.g., 1mL or 3mL) with a 20-27G needle for drawing the diluent.
• A sterile syringe (e.g., 1mL insulin-type) with a 30-32G needle for administration (not covered in this guide).
• Alcohol swabs for disinfecting the vial stopper.
• Sterile gloves and a clean, dedicated preparation area.

Using the correct, sterile materials is fundamental to safe and effective product preparation. Never use bacteriostatic saline or any other diluent unless specified by the manufacturer.

The reconstitution process must be performed carefully to avoid denaturing the protein complex. The objective is to gently dissolve the lyophilized powder without creating foam or agitation.

1. Prepare the Vial: Remove the protective plastic cap from the Hutox vial. Disinfect the exposed rubber stopper with an alcohol swab and allow it to air dry.
2. Draw the Diluent: Using a sterile syringe, draw up the required amount of 0.9% sterile saline solution according to your desired final concentration (refer to the dilution table below).
3. Introduce the Diluent: Slowly and gently inject the saline into the Hutox vial. Angle the needle toward the side wall of the vial to allow the saline to run down and mix with the powder, minimizing foaming and agitation.
4. Dissolve the Toxin: Gently swirl the vial to mix the contents. Do not shake or vigorously agitate the vial, as this can damage the neurotoxin molecule. The solution should become clear, colorless, and free of particulate matter within a few minutes.
5. Inspect the Final Solution: Before use, visually inspect the reconstituted solution. It should be clear and without any visible particles. If the solution is cloudy, discolored, or contains particulates, it must be discarded.

The reconstituted Hutox is now ready for drawing into administration syringes for clinical application. For sourcing a full range of neurotoxins, you can view the complete Botulinum toxin / neurotoxin catalog for your clinic.

The final concentration of the reconstituted Hutox solution depends on the volume of sterile 0.9% sodium chloride added to the 100-unit vial. The table below provides common dilution references for professional use. The choice of dilution is determined by the trained practitioner based on the intended application.

This table is for reference only. Professionals must calculate and verify all dilutions prior to use. Sourcing larger format vials like Botulax 200unit may offer different cost-per-unit efficiencies for high-volume clinics.

Correct temperature control is critical for maintaining the stability of Hutox. Strict adherence to storage protocols is required to ensure product integrity from sourcing to use.

Unopened Vials: Unopened, lyophilized Hutox vials should be stored in a refrigerator at a temperature of 2°C to 8°C (36°F to 46°F). It can also be stored frozen at or below -5°C (23°F). Do not expose to light or extreme temperatures outside this range.

Reconstituted Solution: Once reconstituted, the solution should be used promptly. Manufacturer guidelines generally recommend storing the reconstituted solution in a refrigerator at 2°C to 8°C. It is advisable to use the product within 24 hours of reconstitution. The vial should be clearly labeled with the date and time of reconstitution. Do not freeze the reconstituted solution.

Any unused solution after the recommended period should be safely discarded according to local medical waste regulations. Proper inventory management, similar to that discussed in our professional sourcing guide for VOM Light Filler, helps minimize waste and ensures product is always used within its optimal stability window.